How to Replace the Replacement Key Battery For the Saab 9-3
Saab owners have a unique procedure to add a second key. It requires dealer service using the handheld computer known as Tech-2. Then a new car key and transponder need to be bought and programmed to the car.
Rotate your keys to stop one from wearing out quicker than the next. This will also help to keep your keys in top condition.
Replacement Case
In contrast to the traditional Saab keys of old keys, the new key fobs have electronics inside which makes it hard to make a copy. That has made car theft much more difficult than it was a few years ago. However, it has made replacing lost keys a more expensive task.
Saab 9-3 owners must have two keys working. If one is lost, it costs a lot to get another one for the car, as it requires replacing the CIM module and programming the locking cylinders. Dealers will typically charge $100-$200 to complete this.
There are a few ways to avoid these expensive. Certain parts suppliers will utilize the code of an extra key to cut a new metal blade for less than what the dealer charges. The key must, however, be identical to the original in order to function within your car.
You can also replace the case yourself by following these steps. You'll need a flathead and a lot of patience. With the screwdriver, pry apart the plastic and remove the emergency key. Once the case is open take out all electronic components and place them into the new case. Insert the correct key and badge into the case.
Replacement Battery
The replacement battery for the Saab 9-3 is a cheap part that can be replaced quickly and easily. saab 9-5 key replacement demonstrates how you can replace the remote fob battery in just four easy steps. This tutorial can be used for any modern saab key fob, however, the procedure may differ slightly.
This button is usually located next to the Saab logo on the back of the fob. The button is usually found on the back of your fob, right next to the Saab Logo. Use a flathead screwdriver to insert the screwdriver into the small hole on this button. This should be sufficient to open the fob case in order to change the battery.
After the new battery CR1632 is in place, you can reassemble the remote key fob and then program it to your car. The procedure should take no more than an hour at most. It's a simple process that does not require any special equipment.
The process is a bit more complicated if you've lost the key, but it's possible. The dealer will have to verify the VIN of the car, and then order a new key blade and TWICE module with the exact unique code. After that, they will be required to cut the replacement key and then program it using a new software tool called MDI.
Replacement Key Fob
The key fob is a device that locks and unlocks your car, it has an internal battery. Batteries are able to last for a short time and eventually will die. This is a frequent issue in all vehicles. The good news is you can replace the battery in most key fobs, and not have to replace the entire case. You can purchase fobs replacements on Amazon that come with all the electronic components already installed, so you can just pop open the case and replace the old batteries. It's important to note that you'll need take out the emergency key first, and you can do this by inserting a small flathead screwdriver into the slot found in the middle of the case. The case will split when you turn the screwdriver around it.
When you are ready to replace the keys ensure that you have spare keys, because this can cut down the total cost by a substantial amount. If you have an extra key, you can request the dealer to cut it and program it to your vehicle. This is less expensive than purchasing a new fob.
It is possible to add another key to your car If you don't already have one, however it requires lots of research and effort. The cost of adding a second key is around a hundred dollars and it also requires the programming of the car's computer. This can be done by a professional, however it's a costly choice for the majority of owners.
Replacement Ignition
The new SAAB 9-3 uses an advanced alarm system built around a key code. If you lose only one key, it could be costly to get another one, as the car has to have a special computer added and be programmed to accept a brand new key. Even a dealer can charge hundreds of dollars to program a new key when they are not able to do it.
If you've lost your only working key, a dealer will repair the computer in your car (known as the CIM or SAAB TWICE) in order to make the replacement, and will charge you the highest price for it. We can reprogram the current EEPROM on your car's computer to make it prepared for a new key. This will save you more than 50% of what you would pay at a dealer.
If you've owned a 9-3 from SAAB for many years, you know that the ignition keys are not very durable. They can become extremely sticky, and the buttons can fall off at times and you should think about purchasing a new one if yours isn't functioning properly. Luckily, replacing the ignition key isn't as difficult as it seems, and it is fairly easy to do using the right tools.